Views: 0 Author: Site Editor Publish Time: 2026-10-28 Origin: Site
A steel plant in Vietnam or Indonesia runs continuous operations. Round slings are used to move billets, coils, and fabricated components—often near furnaces, cooling beds, and hot metal handling areas. The air is humid year-round. The combination of heat and moisture creates a degradation environment that standard synthetic slings are not always equipped to handle.
Lishenflex has been manufacturing synthetic round slings for decades, and our experience with steel industry applications shows that material selection and moisture management are the two critical factors for sling performance in Southeast Asian steel plants.
Standard polyester round slings are rated for use and storage between -40°C and 100°C under EN 1492-2 . In a steel plant, this ceiling is easily exceeded near furnaces, hot slabs, or cooling beds. Olsen Chain and Cable warns that equipment left on hot steel decks, near welding operations, or around furnaces can experience excessive heat that weakens fibers and reduces sling strength .
For steel plant applications where ambient or radiant heat is present, polyester alone is insufficient.
Aramid round slings—such as those with para-aramid cores—offer dramatically higher temperature resistance. Product specifications for Lift-All aramid round slings list a maximum operating temperature of 350°F (176°C) with a range of -60°F to +350°F . CERTEX UK notes that slings for high-temperature operations should incorporate aramid fibres or thermal insulation coatings to prevent degradation .
For steel plant lifting near furnaces or hot metal, aramid round slings are the appropriate choice. They maintain strength at temperatures that would permanently damage polyester.
Even with aramid cores, protective sleeves add a layer of defense against radiant heat and abrasion. Aramid slings typically use nylon or heat-resistant sleeves to shield the load-bearing core . In areas of intense radiant heat, thermal barriers or additional protective covers should be considered.
High humidity is a constant in Southeast Asian steel plants. While polyester is less affected by moisture than nylon, moisture trapped in the sling cover can still cause problems. Olsen Chain and Cable notes that high humidity and condensation contribute to equipment degradation, and that improper storage in damp environments exposes gear to unnecessary moisture repeatedly .
For nylon round slings, the humidity risk is more severe. Nylon absorbs moisture and loses strength when wet. In a humid steel plant, this loss can persist if slings do not dry completely between uses.
Wet or damp slings stored in dark, humid conditions are vulnerable to mildew growth. The CCOHS lists mold, mildew, and rotting as conditions that weaken slings and require removal from service . In tropical steel plants, slings that are used, become wet from rain or process water, and are then stored without drying are at high risk.
Storage practice: Slings must be completely air-dried before storage. Hanging in a well-ventilated area is essential.
A damaged cover allows moisture to reach the load-bearing core. The Gunnebo Lifting guidance notes that damage at the cover—where load-bearing core yarn is visible—is a sign of defect requiring removal from service . In humid environments, a compromised cover accelerates moisture ingress and internal degradation.
Per Olsen Chain and Cable, summer or high-heat conditions require more frequent inspections and close attention to specific indicators :
Synthetic slings showing fading, stiffness, cuts, abrasion, or damaged stitching
Hooks, shackles, and fittings with bending, cracks, excessive wear, or heat discoloration
Missing or unreadable identification tags
For steel plant round slings specifically, add these checks:
Heat damage: glazed, melted, or charred surfaces; stiffness without visible charring
Cover damage: any breach exposing the inner core or warning sleeve
Moisture: dampness inside the cover; musty odor indicating mildew
UV degradation: fading or bleaching from outdoor storage or sunlight exposure
Inspection frequency: In steel plant environments with heat and humidity, pre-use inspection before every lift is mandatory. Periodic inspections should be conducted monthly to quarterly, not annually, given the severe service conditions.
Olsen Chain and Cable emphasizes that improper storage causes problems to get worse and that dry, well-ventilated storage areas help reduce corrosion and extend equipment life .
For Southeast Asian steel plants, storage requirements are:
Indoor, shaded, and dry—away from rain, condensation, and process water
Away from direct sunlight—UV degrades synthetic fibers
Away from heat sources—furnaces, steam pipes, and hot surfaces
Well-ventilated—to allow any residual moisture to escape
Hung or laid flat—never folded under pressure or stored on damp floors
Inspected before storage—damaged slings must not be returned to inventory
Round slings for Southeast Asian steel plants must contend with both heat and humidity—a combination that accelerates degradation and demands careful material selection.
Key takeaways:
Standard polyester is limited to 100°C—insufficient for many steel plant lifting areas
Aramid round slings extend service to 200°C+—appropriate for high-heat zones
Humidity is a hidden threat—moisture weakens nylon and promotes mildew in all synthetic slings
Inspect before every use—check for heat damage, cover integrity, and moisture
Store dry, shaded, and ventilated—never store a wet sling
Increase inspection frequency—monthly to quarterly for severe service
Lishenflex manufactures round slings in standard polyester for general-purpose lifting, and can supply aramid and high-performance round slings for demanding high-temperature applications. Our products meet EN 1492-2 and ASME B30.9 standards, with clear temperature ratings and inspection guidance.
If you need assistance selecting the right round sling for your steel plant’s heat and humidity conditions—or need help establishing an inspection and storage program for your facility—please send an email to sales@lishenflex.com, and our technical team will provide one-on-one support.